Back to the main page Back to category Suzuki
Bike details
1990 Suzuki LT250R
Estimated price for orientation: 2 500 $
Category: Suzuki
Class:
Description Condition: Used: A vehicle is considered used if it has been registered and issued a title. Used vehicles have had at least one previous owner. The condition of the exterior, interior and engine can vary depending on the vehicle's history. See the seller's listing for full details and description of any imperfections. See all condition definitions- opens in a new window or tab ... Read moreabout the condition Year: 1990 VIN (Vehicle Identification Number): JSAAJ12A3L2100089 Engine Size (cc): 260 Make: Suzuki Transmission Type: Manual Model: LT250R Exterior Color: Black Type: Race/Sport Drive Train: 2-Wheel Drive Vehicle Title: Clear For Sale By: Private Seller
1990 Suzuki LT250R Every part on this bike is either rebuilt or brand new. It hasn't been riden off road since being put together, only a few times on the pavement for tuning. It's still not currently tuned correctly. I will supply to the buyer all the jets and needles I have for the carb, but they will have to supply their own computer to program the ignition system. It has to be a Windows based computer that can run MSD's Pro-Data+ software. The engine was built from parts sourced from and recommended by FTZ Racing, they calculated the motor should make 55-60HP on gas when tuned correctly. The motor currently has a brand new Mikuni 38mm carb on it that is setup to run on gas, I also have a 39/41.5mm Mikuni taper bore carb that can be used to run the motor on alcohol or nitro. I'll be including the extra carb and all other parts that I have for the bike, including a set of sand tires and an aluminum skid plate. The only reason I'm selling is because of a back and leg injury. This is going to be a really good deal for someone, I have over $10,000 into this build at this point and that's not including the extra parts I have or the original price of the bike. I can ship this if the buyer arranges it, I would recommend picking it up or hiring a shipping company that can pick it up as it is. If you can only find someone that will ship it on a pallet the measurements are 48"W X 78"L X 48"T and I would estimate the weight to be between 350-400lbs with the extra parts and packaging. Below I have a list of most of the parts that I could think of. Feel free to ask any questions.Engine:
FTZ Mid-High Ported Cylinder
Wiseco Piston w/ Thrust Washer Delete
Hot Rods Crank and Rod
Pro Design Cool Head w/ FTZ Dome
EBC Clutch w/ Billet Hard Anodized Basket and New Factory Hub and Pressure Plate
V-Force 3 Reed Cage
FTZ Aluminum Intake
Mikuni 38MM Flat Slide Carb
New Factory Flywheel
FTZ High Rev Inframe Pipe and Billet Silencer
All New Bearings in Engine
SB Designs Chain Guard/Case Saver
All Engine Hardware is New
All Shift Forks Have Been Replaced
Custom Made Silicone Radiator Hoses
All New Power Valve Components
LT500R Fuel PetcockElectrical:
MSD CDI Programmable Single Cylinder Igniton
MSD Coil and Plug Wire
Ricky Stator Regulator/Rectifier
Ricky Stator 130W High Output Stator Coils
New Factory Primary Coil and Pick Up
Spal Electric Fan with Thermostat Control
Trail Tech Vaper Digital Dash w/ Speedo, Tach, and Coolant Temp
Trail Tech Twin HID Headlights (Low Beam is Flood Only and High Beam is Spot and Flood)
LED Tail Light and Brake Light
Front Mounted AGM Battery
Autometer Cobalt EGT GaugeFrame/Suspension:
New Works Triple Rate Remote Reservoir Front Shocks
New Ohlins Progressive Rate Remote Reservoir Adjustable (Compression and Rebound) Rear Shock
+2"/+2" Chromoly Front Control Arms
+4" Swingarm
-4" - +4" Adjustable Lonestar Rear Axle
Rad Manufacturing Taper Bearing Rear Axle Carrier
JL ATV Steering Stabilizer
New Factory Ball Joints and Tierod Ends
All New Bearings and Seals on All Suspension Parts
All Brake Parts Are New or Rebuilt Using Factory Parts
Stainless Brake Rotors
T.M. Designworks Chain Guides and RollersBody:
All New Maier and Factory Plastics
Graydon Nerf Bars
PRM 6-Pack Rack
DG Front Bumper
Motion Pro Quick Ratio Twist Throttle
SB Designs Rear Fender Supports
Renthal Handlebars
Jet Trim Seat
Description
| Condition: | Used: A vehicle is considered used if it has been registered and issued a title. Used vehicles have had at least one previous owner. The condition of the exterior, interior and engine can vary depending on the vehicle's history. See the seller's listing for full details and description of any imperfections. See all condition definitions- opens in a new window or tab ... Read moreabout the condition | Year: | 1990 |
| VIN (Vehicle Identification Number): | JSAAJ12A3L2100089 | Engine Size (cc): | 260 |
| Make: | Suzuki | Transmission Type: | Manual |
| Model: | LT250R | Exterior Color: | Black |
| Type: | Race/Sport | Drive Train: | 2-Wheel Drive |
| Vehicle Title: | Clear | For Sale By: | Private Seller |
1990 Suzuki LT250R Every part on this bike is either rebuilt or brand new. It hasn't been riden off road since being put together, only a few times on the pavement for tuning. It's still not currently tuned correctly. I will supply to the buyer all the jets and needles I have for the carb, but they will have to supply their own computer to program the ignition system. It has to be a Windows based computer that can run MSD's Pro-Data+ software. The engine was built from parts sourced from and recommended by FTZ Racing, they calculated the motor should make 55-60HP on gas when tuned correctly. The motor currently has a brand new Mikuni 38mm carb on it that is setup to run on gas, I also have a 39/41.5mm Mikuni taper bore carb that can be used to run the motor on alcohol or nitro. I'll be including the extra carb and all other parts that I have for the bike, including a set of sand tires and an aluminum skid plate. The only reason I'm selling is because of a back and leg injury. This is going to be a really good deal for someone, I have over $10,000 into this build at this point and that's not including the extra parts I have or the original price of the bike. I can ship this if the buyer arranges it, I would recommend picking it up or hiring a shipping company that can pick it up as it is. If you can only find someone that will ship it on a pallet the measurements are 48"W X 78"L X 48"T and I would estimate the weight to be between 350-400lbs with the extra parts and packaging. Below I have a list of most of the parts that I could think of. Feel free to ask any questions.Engine:
FTZ Mid-High Ported Cylinder
Wiseco Piston w/ Thrust Washer Delete
Hot Rods Crank and Rod
Pro Design Cool Head w/ FTZ Dome
EBC Clutch w/ Billet Hard Anodized Basket and New Factory Hub and Pressure Plate
V-Force 3 Reed Cage
FTZ Aluminum Intake
Mikuni 38MM Flat Slide Carb
New Factory Flywheel
FTZ High Rev Inframe Pipe and Billet Silencer
All New Bearings in Engine
SB Designs Chain Guard/Case Saver
All Engine Hardware is New
All Shift Forks Have Been Replaced
Custom Made Silicone Radiator Hoses
All New Power Valve Components
LT500R Fuel PetcockElectrical:
MSD CDI Programmable Single Cylinder Igniton
MSD Coil and Plug Wire
Ricky Stator Regulator/Rectifier
Ricky Stator 130W High Output Stator Coils
New Factory Primary Coil and Pick Up
Spal Electric Fan with Thermostat Control
Trail Tech Vaper Digital Dash w/ Speedo, Tach, and Coolant Temp
Trail Tech Twin HID Headlights (Low Beam is Flood Only and High Beam is Spot and Flood)
LED Tail Light and Brake Light
Front Mounted AGM Battery
Autometer Cobalt EGT GaugeFrame/Suspension:
New Works Triple Rate Remote Reservoir Front Shocks
New Ohlins Progressive Rate Remote Reservoir Adjustable (Compression and Rebound) Rear Shock
+2"/+2" Chromoly Front Control Arms
+4" Swingarm
-4" - +4" Adjustable Lonestar Rear Axle
Rad Manufacturing Taper Bearing Rear Axle Carrier
JL ATV Steering Stabilizer
New Factory Ball Joints and Tierod Ends
All New Bearings and Seals on All Suspension Parts
All Brake Parts Are New or Rebuilt Using Factory Parts
Stainless Brake Rotors
T.M. Designworks Chain Guides and RollersBody:
All New Maier and Factory Plastics
Graydon Nerf Bars
PRM 6-Pack Rack
DG Front Bumper
Motion Pro Quick Ratio Twist Throttle
SB Designs Rear Fender Supports
Renthal Handlebars
Jet Trim Seat
FTZ Mid-High Ported Cylinder
Wiseco Piston w/ Thrust Washer Delete
Hot Rods Crank and Rod
Pro Design Cool Head w/ FTZ Dome
EBC Clutch w/ Billet Hard Anodized Basket and New Factory Hub and Pressure Plate
V-Force 3 Reed Cage
FTZ Aluminum Intake
Mikuni 38MM Flat Slide Carb
New Factory Flywheel
FTZ High Rev Inframe Pipe and Billet Silencer
All New Bearings in Engine
SB Designs Chain Guard/Case Saver
All Engine Hardware is New
All Shift Forks Have Been Replaced
Custom Made Silicone Radiator Hoses
All New Power Valve Components
LT500R Fuel PetcockElectrical:
MSD CDI Programmable Single Cylinder Igniton
MSD Coil and Plug Wire
Ricky Stator Regulator/Rectifier
Ricky Stator 130W High Output Stator Coils
New Factory Primary Coil and Pick Up
Spal Electric Fan with Thermostat Control
Trail Tech Vaper Digital Dash w/ Speedo, Tach, and Coolant Temp
Trail Tech Twin HID Headlights (Low Beam is Flood Only and High Beam is Spot and Flood)
LED Tail Light and Brake Light
Front Mounted AGM Battery
Autometer Cobalt EGT GaugeFrame/Suspension:
New Works Triple Rate Remote Reservoir Front Shocks
New Ohlins Progressive Rate Remote Reservoir Adjustable (Compression and Rebound) Rear Shock
+2"/+2" Chromoly Front Control Arms
+4" Swingarm
-4" - +4" Adjustable Lonestar Rear Axle
Rad Manufacturing Taper Bearing Rear Axle Carrier
JL ATV Steering Stabilizer
New Factory Ball Joints and Tierod Ends
All New Bearings and Seals on All Suspension Parts
All Brake Parts Are New or Rebuilt Using Factory Parts
Stainless Brake Rotors
T.M. Designworks Chain Guides and RollersBody:
All New Maier and Factory Plastics
Graydon Nerf Bars
PRM 6-Pack Rack
DG Front Bumper
Motion Pro Quick Ratio Twist Throttle
SB Designs Rear Fender Supports
Renthal Handlebars
Jet Trim Seat